Kraus-usa Kralin Wireless Access Point 54MB Single Port Cod. User Manual download pdf (Page 10)

www.kraun.it 10

User’s Manual

2. Enter a simple description of the wireless station in the Description

field. For example: Wireless station A.

3. Privilege - Selects the privileges for this entry, one of Allow / Deny /

64-bit / 128-bit / 152-bit.

4. WEP Key - If you select 64-bit, 128-bit or 152-bit in the Privilege field,

enter any combination of hexadecimal digits (0-9, a-f, A-F) in the

specified length. For example: 2F34D20BE2.

5. Status - Select Enabled or Disabled for this entry on the Status pull-

down list.

6. Click the Save button to save this entry.

To add additional entries, repeat steps 1-6.

Note: When 64-bit, or 128-bit, or 152-bit is selected, WEP Key will be

enabled.

To modify or delete an existing entry:

1. Click the Edit or Delete button in the Modify column in the MAC Ad-

dress Filtering Table.

2. Enter the value as desired in the Add or Modify Wireless MAC Ad-

dress Filtering entry page, and click the Save button.

You can click the Enable All button to make all the entries effective, click

the Disable All button to make all the entries ineffective, click the Delete

All button to delete all the entries.

Click the Next button to go to the next page and click the Previous button

to return to the previous page.

For example: If you desire that the wireless station A with MAC address

00-0A-EB-00- 07-BE be able to access the AP, the wireless station B with

MAC address 00-0A-EB- 00-07-5F not be able to access the AP, and the

wireless station C with MAC address 00-0A-EB-00-07-8A be able to ac-

cess the AP when its WEP key is 0123456789ABCDEF0123456789, while

all other wireless stations cannot access the AP, you should configure

the Wireless MAC Address Filtering list following these steps:

1. Click the Enable button to enable this function.

2. Select the radio button: Deny the stations not specified by any ena-

bled entries in the list to access for Filtering Rules.

3. Delete or disable all entries if there are any entries already.

4. Click Add New... button and enter the MAC address 00-0A-EB-00-

07-BE in the MAC Address field, enter wireless station A in Descrip-

tion field, select Allow in the Privilege pull-down list and select Ena-

bled in Status pull-down list. Click the Save and the Return button.

5. Click the Add New... button and enter the MAC address 00-0A-EB-

00-07-5F in the MAC Address field, enter wireless station B in the

Description field, select Deny in the Privilege pull-down list and select

Enabled in the Status pull-down list. Click the Save and the Return

button.

6. Click the Add New... button and enter the MAC address 00-0A-EB-

00-07-8A in the MAC Address field, enter wireless station C in the

Description field, select 128-bit in the Privilege pull-down list, enter

2F34D20BE2E54B326C5476586A in the WEP Key field and select

Enabled in the Status pull-down list. Click the Save and the Return

button.

The filtering rules that configured should be similar to the following

list:

Figure 5-15: The filtering list

Note:

a) If you select Allow the stations not specified by any enabled entries in

the list to access for Filtering Rules, the wireless station B will still not

be able to access the AP, however, other wireless stations that are

not in the list will be able to access the AP.

b) If you enable the function and select the Deny the stations not speci-

fied by any enabled entries in the list to access for Filtering Rules, and

there are not any enable entries in the list, thus, no wireless stations

can access the AP.

5.4.5 Wireless Statistics

This page shows MAC Address, Current Status, Received Packets and

Sent Packets for each connected wireless station.

Figure 5-16: The AP attached wireless stations

• MAC Address - The connected wireless station’s MAC address

• Current Status - The connected wireless station’s running status, one

of STA-AUTH / STA-ASSOC / STA-JOINED / WPA / WPA-PSK / WPA2 /

WPA2-PSK / AP-UP / AP-DOWN / Disconnected

• Received Packets - packets received by the station

• Sent Packets - packets sent by the station

You cannot change any of the values on this page. To update this page

and to show the current connected wireless stations, click on the Re-

fresh button.

If the numbers of connected wireless stations go beyond one page, click

the Next button to go to the next page and click the Previous button to

return the previous page.

Note: This page will be refreshed automatically every 5 seconds.

5.5 DHCP

Figure 5-17: the DHCP menu

There are three submenus under the DHCP menu (shown in figure 5-

17): DHCP Settings, DHCP Clients List and Address Reservation. Click any

of them, and you will be able to configure the corresponding function.

The detailed explanations for each submenu are provided below.

5.5.1 DHCP Settings

The System can be set up as a DHCP (Dynamic Host Configuration Pro-

tocol) server, which provides the TCP/IP configuration for all the PCs that

are connected to the system on the LAN. The DHCP Server can be con-

figured on the page (shown in figure 5-18):

Figure 5-18: DHCP Settings

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 16 17

Comments to this Manuals

No comments

Kraus-usa Kralin Wireless Access Point 54MB Single Port Cod. User Manual Page 10

Comments to this Manuals